Clean-Headlights-Before-Tinting

How to install Headlight Tint Film on a car ?

Share this

More and more people will own their own car, but how to make their baby car more beautiful, we can start with some simple ways to dress the eyes of the car with distinctive beauty.

Today, we’ll introduce the headlight Tint Film of LinkedGo. By the way, we’ll also tell you how to install it.

If you’re interested, you can buy our products directly. Try to make your car have beautiful eyes.

Recommended Install Headlight/Taillight Tint Tools

  • Rapid Clear
  • Squeegee
  • Razor Blade
  • Heat Gun or Hair Dryer

Install Tips

  • Ideal application temperature range is between 70º to 80º F (21º to 27º C).
  • When possible, turn on your lights to help increase the surfacetemperature.
  • Surfaces must be clean and dry prior to application.
  • When removing precut smoked tint pieces from the backing it is best to continuously spray both sides of the film with an application fluid to mild soap solution to prevent premature adhesion of the kit to itself.
  • Clean your areas thoroughly with a solution such as Rapid Prep.
  • Do not apply during periods of high relative humidity (i.e., when it’s raining).
  • Do not bend vinyl film back and forth as this causes the adhesive to wrinkle when applying.

Step 1: Preparation and Cleaning

To be honest, headlight and taillight installation is almost the same, the difference is the radian of the lamp, but this does not care as long as the rational use of heat gun

Begin by cleaning the your headlight housing, the lens and the surrounding areas. For proper adhesion, clean all surfaces using a soap of water, and remove all dust, oil and residues not only from the windows but from the surrounding panels and even the area in which you’ll be tinting.

Cleaning headlight tint film


Note: Prior to cleaning test solution in an inconspicuous area. Use a clean, lint-free cloth to cleanse the application area. Insure the lens is dry and all oils and residues have been removed prior to application. A good test is to see if masking tape will stick to the application surface, if it sticks then the surface is ready for application. If it does not stick then further cleaning may be necessary.

Step 2: Spray and Lubricate Lenses

Spray Headlight Tint Application Fluid

Spray a liberal amount of the soap water onto the light which will allow you to reposition the film during the application process. Be sure to include gaskets and trim around the lights as well.

Step 3: Remove Headlight/Taillight tint film Liner

Peel Headlight Tint Cover from Liner

As always, mist your fingers, and spray the Rapid Tac on the tint as well.

In order to remove the tint from the liner, carefully and slowly lift a corner and begin to peel the liner. Spray both sides of the tint with application soap water. This will allow you to reposition the film on the light as well as preventing the tint from sticking to itself.

Step 4: Apply Headlight tint film

How To Apply Headlight Tints Film

Having sprayed the light with application soap water, apply the wet, adhesive side of the film to the lens.

Reposition the film to align it to the edges. You may use the application tabs if they are available on your kit.

Not all kits are designed with these tabs.

Note: The film may appear to be “short” or “too large” at this stage of the installation. This is because the film has not been heated and stretched yet or trimmed.

Step 5: Spray Headlight/Taillight Tint

Spray HeadLight Tint Film

Spray the outside of the film with soap and water solution again. This will reduce scratching. Spray the area once again to allow repositioning.

Step 6: Squeegee on Headlight/Taillight Tints

Squeegee Headlight Tint On Lens

For flatter areas, apply pressure to one end of the film so that it begins to adhere to one end of the area. Using a squeegee, press down and squeegee the film with smooth sweeping motions. If this is being done properly, you will see the water exit from underneath the film. Do this across the remainder of the area.

Important Installation Notes

If large bubbles are present, peel up the film to that area and apply again. LinkedGo Headlight/Taillight vinyl film is very forgiving when both the area and the adhesive side of the film is wet. Keeping the film wet allows you to pull and reapply numerous times if not satisfied with results prior to heating the film.

For headlight tint kits with slits spray the outside of the film with solution again. This will reduce scratching. Spray the light once again. Proceed as above being sure to liberally apply the solution to both sides of the film. When the film is stretched into position one of the sections or flaps of the film will naturally fall over the other. Lightly smooth the flap down until flat. Using a razor gently score away the overlapping film until you can easily pull the excess film away.

For lights with large curves (the most common lights on the market today), spray the outside of the film with solution again. This will reduce scratching. Spray the light once again. Apply pressure to the center of the film on the light with a squeegee so that it begins to adhere to one end of the light. It may be easier to have a partner help you by holding the film as you begin the next step. Gently begin to heat the film on one end from the center with a hair dryer or heat gun on a low setting. Take your time in heating the film, you do not want to melt the film.

Apply the remainder of the film by moving in a spiral or circular motion working outwards towards the edge of the light. Keep the film “warm” by continually heating it will allow it to stretch up to 2% to 5% and conform. This is the only way you can apply tint to a curved light unless the kit has slits which are intended to be overlapped and cut-away.

Step 7: Heat the Tint

How to Install Headlight Tint with Heat

Using a heat gun heat the tint to aid in shrinking and curing the film.

Step 8: Trim Away Excess

Trim Excess Headlight Tint Film

Remove excess vinyl which may hang over the edges.

Step 9: Allow to Cure & Pop Any Bubbles

How to Pop Bubbles in Headlight Tint

Allow film dry for a minimum of 30 minutes and carefully wipe off any excess solution. If all moisture has not been properly removed from under the film some fogginess may occur. This is completely normal. Film is breathable and porous – cloudiness/fog will evaporate with a few days to a few weeks. Depending on film thickness and sunlight/heat exposure. Any surface texture, scratches, or ripples will also disappear during this curing process.

Note: Adhesion may be difficult in cold weather, humid areas or if the surface has not been properly cleaned prior to application. After 24 hours, if there are any small bubbles you may proceed to pop them with a sharp needle. Pop them and then use a squeegee to press out air or fluid. DO NOT spray any more application fluid at this point.

Let me know what your next car project will be? What color do you like best to decorate your headlights? Let me know in the comments below. Also, let me know if you have any questions about which headlight tint to use with your car. I’d love to hear them!

Add a Comment

Your email address will not be published. Required fields are marked *